NewLook Clear 32 is a clear finish that has multiple applications, but it is not considered a traditional "sealer". It can be used in combination with abrasive grit. It can also be used as a "primer" instead of the Solid Colour Stain when antiquing raw, virgin concrete with the Translucent Colour Enhancer. Many use Clear 32 in multiple layers on interior applications of NewLook Concrete Colour Stains to provide a sacrificial layer. |
Please read the NewLook Technical Information Sheet for information regarding the limited product warranty. |
Yes. NewLook Concrete Colour Stains are compatible with all currently known sealers. It is recommeded to use the NewLook Concrete Sealer.
|
Yes, due to extreme UV conditions in Australia Newlook colour stain must be sealed
|
Not much, but always remember that it is absolutely critical that the surface is prepared correctly, otherwise, NewLook will likely have adhesion problems. Typically, pressure washing is all that is required to open up the surface pores. The rule of thumb is that if there is anything on the concrete that would prevent NewLook from penetrating (sealers, paints, "cure and seal" agents, dirt, oil, grease, glue, gum, etc.) then that substance needs to be cleaned off or removed before applying NewLook.
Use a pressure washer with 3000 PSI and a capacity of 4 gallons per minute. Use a 15° or 25° fan tip (never use a 0° tip). Do not bear down on the concrete as it can change the surface texture. Keep in mind that there is a big difference between simply hosing off the concrete and really pressure washing it well. In areas where pressure washing is not possible, a floor-scrubbing machine with a cleaner is acceptable. Use a mild cleaner that contains no acid.
Hard-troweled or polished surfaces are generally too dense to allow NewLook to penetrate. Use NewLook Eco Acid to profile the surface. It is important to thoroughly rinse off any remaining residue or dust before applying NewLook. |
The large size (32 oz.) NewLook Solid Colour Stain kit covers an average of 350 sq ft twice, meaning two separate applications*. The small size (4 oz.) NewLook Solid Colour Stain kit covers an average of 45 sq ft twice*. The large size (16 oz.) NewLook Translucent Colour Enhancer kit covers approximately 350 sq ft. The small size (4 oz.) NewLook Translucent Colour Enhancer kit covers approximately 45 sf. The NewLook Clear 32 kit (32 oz.) covers approximately 600 sq ft.
*Estimating a job should be based on its square footage. For example, if you were trying to stain 700 sf then you would use two large size NewLook Solid Colour Stain kits (350 + 350 = 700). Coverage is based on the porosity of the surface, moisture content of the substrate, and method of application. |
Not long. You can apply NewLook when the surface is damp, but not when there is standing water. Many contractors pressure wash in the afternoon and apply NewLook the next morning.
|
Absolutely. NewLook Solid Colour Stain was designed to do just that. Generally, only two applications are needed to hide most stains. Under some circumstances a third application could be required to completely cover any discoloration (only occasionally and when light colors are applied over very blotchy concrete). Be sure to clean the concrete thoroughly before applying NewLook.
|
NewLook is designed to provide even and consistent color coverage between old and new concrete, patches, etc. If adjacent areas differ in texture, which is commonly the case, the stain could look slightly different due to wear and tear or other texture differences. In extreme situations staining the concrete to a single color could accentuate the texture differences.
|
Yes. As soon as the application of NewLook has dried a new color can be applied. You do not need to remove the previous application of NewLook. Depending on the time between applications, additional cleaning may be required.
|
The concrete temperature is most important. The concrete surface needs to be between 50° (and rising) and 95°. If the concrete temperature is too cold NewLook will take a long time to dry. If it is too hot NewLook can "flash dry" and re-brooming NewLook will be impossible- allowing streaks or discoloration.
|
NewLook Solid Colour Stain consist of a proprietary blend of colours and pigments that need to be suspended throughout the application process. It is necessary to re-broom NewLook to ensure that the colour pigments are suspended consistently so that the correct colour is achieved. Typically, NewLook Solid Colour Stain only needs to be re-broomed a few times. You can stop re-brooming when there is no Colour variation as you re-broom over NewLook or when it is dry. For more information, please view the application videos in the Videos/Data section.
|
No. Spraying is not recommended for NewLook Solid Colour Stains. The special pigments in the NewLook Solid Colour Stain may clog the spray nozzle. Applying it with the NewLook Applicator Brush is the best and preferred method.
However, you can spray on the NewLook Translucent Colour Enhancer. It does not require re-brooming like the NewLook Solid Colour Stain. |
NewLook is a penetrating concrete stain that lasts as long as the concrete itself. In fact, NewLook&apost;s bond is so tenacious that when you pressure wash the concrete, you will actually ruin the surface before removing any colour - NewLook is that permanent!
The wear and tear (traffic, weather, use, etc.) of the concrete surface may eventually affect NewLook enough to necessitate a maintenance application. Fortunately, NewLook is completely opaque and does not need to be removed for maintenance applications. Interior applications of NewLook that have been sealed or waxed will last much longer. NewLook generally lasts as long as an acid stain, if not much longer. |
Simply wipe NewLook off the surface with a damp towel if it is still wet. If NewLook has dried it is necessary to remove it either chemically or mechanically. You can try paint strippers or light sanding. The best prevention is to mask off areas and be careful during application. Once NewLook has stained the concrete it is tough to remove.
|
You can either apply multiple layers of the NewLook Translucent Colour Enhancer or add a NewLook Colour Additive (same colour) to the Enhancer in order to intensity the hue. For example, if the 295 Light Oak Enhancer is not intense enough, simply add a 295 Light Oak Colour Additive. Up to 4 NewLook Colour Additive can be added to a 16 oz NewLook Translucent Colour Enhancer kit for a very intense colour. NewLook Colour Additives come in each of the same 80 standard colours as the NewLook Translucent Colour Enhancer.
|
The NewLook Translucent Colour Enhancer can be applied with a NewLook Applicator Brush, pump sprayer, airless sprayer, nap roller, rag, etc. You will get a different effect depending on the application medium. You are only limited by your imagination. Faux finishing with the NewLook Translucent Colour Enhancer is a skill that is developed through practice.
Note: under normal circumstances, the NewLook Translucent Colour Enhancer is not re-broomed like the NewLook Solid Colour Stain. Once applied, the NewLook Translucent Colour Enhancer should typically be allowed to "flow" and dry naturally. |
Yes. Multiple applications of the NewLook Translucent Colour Enhancer will intensify the colour (and create the appearance of depth), or the NewLook Colour Additive can be used to intensify the hue.
|
All you need is a supply of water, a couple of 5 gallon buckets, a NewLook Applicator Brush, a power drill, and a small bristle brush.
|
Not long at all. You can walk on NewLook after only 4 to 8 hours. You can drive on NewLook after only 48 hours, and you can clean NewLook (e.g. pressure wash) after only 1 week. The surface should not get wet for at least 24 hours following application*.
*This is a general rule. In warmer temperatures, time could be less. |
NewLook offers 80 standard colours. You can get each color in the NewLook Solid Colour Stain, the NewLook Translucent Colour Enhancer, and the NewLook Colour Additive. NewLook also offers an unlimited range of colour possibilities with the ability to custom colour match any colour desired!
|
